MACH 5 Manual Project64.txt

From ReplayResources
Jump to navigationJump to search

MACH 5 Manual

text included from Project64

Please check the text for credits!


*********

Welcome to Project 64!

The goal of Project 64 is to preserve Commodore 64 related documents
in electronic text format that might otherwise cease to exist with the
rapid advancement of computer technology and declining interest in 8-
bit computers on the part of the general population.

Extensive efforts were made to preserve the contents of the original
document.  However, certain portions, such as diagrams, program
listings, and indexes may have been either altered or sacrificed due
to the limitations of plain vanilla text.  Diagrams may have been
eliminated where ASCII-art was not feasible.  Program listings may be
missing display codes where substitutions were not possible.  Tables
of contents and indexes may have been changed from page number
references to section number references. Please accept our apologies
for these limitations, alterations, and possible omissions.

Document names are limited to the 8.3 file convention of DOS. The
first characters of the file name are an abbreviation of the original
document name. The version number of the etext follows next. After
that a letter may appear to indicate the particular source of the
document. Finally, the document is given a .TXT extension.

The author(s) of the original document and members of Project 64 make
no representations about the accuracy or suitability of this material
for any purpose.  This etext is provided "as-is".  Please refer to the
warantee of the original document, if any, that may included in this
etext.  No other warantees, express or implied, are made to you as to
the etext or any medium it may be on.  Neither the author(s) nor the
members of Project 64 will assume liability for damages either from
the direct or indirect use of this etext or from the distribution of
or modification to this etext. Therefore if you read this document or
use the information herein you do so at your own risk.

*********

The Project 64 etext of the ~Mach5 fast-loader cartridge~, Converted
to etext by Steve Neas <sneas@ot.com>.  The tilde character [~] has
been used to represent the left arrow key on the Commodore 64.

MACH5F10.TXT, November 1997, etext #304#

*********

ACCESS Software Incorporated

MACH5
Cartridge
Instruction Manual
for
Commodore 128/64
and 1541/1571 disk


CARTRIDGE FAST LOADER

Note: Mach5 is designed for use with the Commodore C128/C64 and 1571
or 1541 or compatible disk drive.


SET UP

1. Make sure that your computer is turned OFF before inserting or
removing your Mach5 CARTRIDGE.

2. Insert the Mach5 CARTRIDGE into the cartridge slot located at the
rear right corner of the computer.

3. Turn on your disk drive(s) and your computer.  After the computer
has been turned on, the words, "Mach-5 V-XX LOADER ENGAGED" will
appear on the screen.


MENU

Type "~M," to display the command menu at any time that the
cursor is flashing.

The following commands are available with Mach5 CARTRIDGE.

COMMAND        FUNCTION


$              List a directory on the screen without erasing the
               program in memory.

               While listing a disk directory to the screen, the
               display scrolling may be paused and unpaused by
               pressing the 'space' bar.

               To load a file from a directory that has been listed
               to the screen, simply move the cursor to the left most
               column next to the file name, and use the appropriate
               command to load the file.  Mach5 will then attempt to
               load the file by accessing the most current drive used
               (see @DN command).

@COMMAND       Send a DOS command to the most current disk drive
               (Example: @i is the same as OPEN 15,DN,15,"I":CLOSE
               15).

               By pressing the '@' key (which is used to send a
               command to the drive) and the 'return', the error
               condition of the most current drive may be displayed.

@DN            This command is essentially the same as the BASIC
               command 'POKE 186,DN' where DN is a drive number from
               8 to 11.  All load, save and DOS commands will refer
               to this most currently designated drive number for
               drive operations.

/FILENAME      The same as LOAD "FILENAME",DN.

£FILENAME      The '£' key, followed by a file name, will not only
               load a BASIC file, but will also immediately run the
               file.
               EXAMPLE: LOAD "FILENAME",DN:RUN.

^FILENAME      The same as LOAD "FILENAME",DN,1.

=FILENAME      The same as SAVE "FILENAME",DN.

~*             The same as LOAD "*",8,1:RUN.  When using the '~*'
               command, if the file does not auto-execute, the file
               will now be made to execute.
               EXAMPLE: LOAD":*",DN,1:RUN.

~P             The same as OPEN 4,4,7:CMD4 (Printer open for
               upper/lower case).

~U             The same as OPEN 4,4:CMD4 (Printer open for upper
               case/graphics).

~C             The same as PRINT#4:CLOSE 4 (Close printer channel).

~L             The same as LOAD "(add FILENAME",DN).

~S             The same as SAVE "(add FILENAME",DN).

~M             Display Mach5 menu.

~R             Disable 1541 drive RATTLE ON ERROR for most current
               drive.  (To re-enable, turn drive off and on).

~D             Disable FAST LOADER and save but retain commands.

~E             Enable MACH DOS routines.

~H             Hard copy print out of the screen.  Works in 'DIRECT'
               mode only.

~O             'O' will restore a BASIC program previously 'NEW'd, or
               restore the program after a system reset.  (This is
               equivalent to the BASIC command 'OLD').

$HHHH          This command will convert and display on the screen
               the hexidecimal, decimal and binary of the 4-digit hex
               number input
               (EXAMPLE: $1F09).

+DDDDD         This command will convert and display on the screen
               the hexidecimal, decimal and binary equivalent of the
               decimal number input
               (Example: +1394).

%BBBBBBBB-     This command will convert and display on the screen
BBBBBBBB       the hexidecimal, decimal and binary equivalent of the
               binary number input
               (Example: %0011101011001000).

@F:DISKNAME,ID This is a 10 second disk format command for use on
               1541 drives.  The diskname must be from 1 to 16
               digits, and the ID must be 2 digits.  When this
               command is invoked, the drive light will NOT turn on
               while formatting, but it will turn on briefly at
               the end of formatting to indicate a successful format.
               If, when the directory is listed, the disk has not
               been properly formatted, simply initialize the drive
               and repeat the format command.


ADDITIONAL INFORMATION

- To disable COMMANDS, but not affect the MACH DOS, type SYS57043.
- To enable COMMANDS ONLY type SYS57054.
- To enable COMMANDS and MACH DOS, type SYS57051.
- To enable MACH DOS only, type SYS57003.

- The directory list command "$" will use the most current drive
number.  You may directly select a device by using the @DN command,
where DN=drive number (8-11).

- Users of SYSRES (TM by Solidus International) can do fast program
file loads with Mach5, but must use conventional BASIC syntax (i.e.
LOAD "FILENAME",DN).

- There are very few programs that will not load with Mach5 engaged.
If a program does fail to load, try typing "~D" to disable the MACH
DOS rather than removing the cartridge.  The time required to load a
program depends on many factors, including booting technique, error
checking, etc.  Speeds up to 500% of normal are possible with long,
single file program loads.  With copy protected programs, it is
usually possible to save a few seconds as well as drive wear by
disabling the drive rattle.  Some programs, however, may not load
properly with the rattle disabled.

- After the computer is first turned on, be sure and wait for the
disk light to go out before accessing the disk with a command such
as "$".

- If a scrambled (non-working) screen occurs when Mach5 CARTRIDGE
and/or a printer interface is connected to your printer the problem
is most commonly a weak or failing power supply.  See your local
Commodore dealer and try a different power supply.


ACCESS SOFTWARE
2561 SOUTH 1560 WEST
WOODS CROSS, UTAH 84087

*********

End of Project 64 etext Mach5 fast-loader cartridge.

*********